John Deere 4210 tractor

John Deere 4210

Power

27 hp

Production

2002-2004

Engine

Diesel, 3-cylinder

Transmission

SyncShift

Drive

2WD/4WD

From the same series:

4115
4310

Introduction

Production Information of John Deere, 4210

The production information of the tractor (4210) includes details about its manufacturing.

Compact Utility tractor
Built in Augusta, Georgia, USA
ManufacturerJohn Deere

Dimension and Tires Information of John Deere, 4210

This section sums up the dimension and tires information of the tractor.

Wheelbase65 inches [165 cm]
Clearance (rear axle)30.1 inches [76 cm]
Length117 inches [297 cm]
Width53 inches [134 cm]
Ag front4.00-15 (2WD)
7.00-14 (4WD)
Ag rear11.2-24

Engine Specifications of John Deere, 4210

Get the specifications for the engine and if different options are available.

Yanmar 3TNE82A
Liquid-cooled
Diesel
3-cylinder
Coolant capacity5.6 qts [5.3 L]
Air cleanerDry
Compression18.5:1
Idle RPM1000-2810
Rated RPM2600
Displacement81.2 ci [1.3 L]
Power (gross)27 hp [20.1 kW]
Bore/Stroke3.23x3.31 inches [82 x 84 mm]
Oil capacity4.0 qts [3.8 L]
Starter power1.6 hp [1.2 kW]
Starter volts12

Transmission Information of John Deere, 4210Y

Discover all variants of transmission available for this tractor model.

Transmission variants 1

Three gears (1-3) plus reverse in three ranges (A-C). Gears can be shifted on the move using the clutch. Tractor must be stopped to shift ranges.
TransmissionSyncShift
Oil capacity25.2 qts [23.8 L]
TypePartially synchronized
Gears9 forward and 3 reverse

Transmission variants 2

Three-range hydrostatic transmission with foot pedals and cruise control. Tractor must be stopped to shift ranges. Automotive cruise control option allows set speed to be adjusted with rocker switch. SpeedMatch option allows a maximum speed to be set and full pedal travel used to achive that speed. LoadMatch option prevents the tractor from stalling during heavy loads. The MotionMatch option enables the acceleration rate to be set to fast or slow.
TransmissionEHydro
Oil capacity27.2 qts [25.7 L]
TypeHydrostatic
GearsInfinite forward and reverse (3-range)
9-speed partially synchronized
Hydrostatic

Mechanical Specs of John Deere, 4210Y

This section summarizes all mechanical information such as the brake system and other specifications.

Two- or four-wheel drive
Wet disc brakes
Two-post fixed ROPS. Two-post folding ROPS optional.
SteeringPower
Final drivesSpur gear
Differential lockMechanical rear

Power Information of John Deere, 4210Y

Discover the power specifications and options available for this tractor model but also PTO (Power Take-off) information.

Rear PTOIndependent
Mid PTOIndependent OptOptional
Engine RPM540@2600
ClutchWet disc
Mid PTO Type2100
Rear PTO Type540 (1.375)

Hydraulics Specifications of John Deere, 4210

Hydraulic system type, pressure, pump flow and valves.

Total flow12.3 gpm [46.6 lpm]
TypeOpen center
Valves5
Pressure2125 psi [146.5 bar]
Capacity6.3 gal (gear) [23.8 L]
Steering flow5.3 gpm [20.1 lpm]
Pump flow7.0 gpm [26.5 lpm]
6.8 gal (hydro) [25.7 L]

Three-Point Hitch of John Deere, 4210

Hitch category and rear/front lift capacity.

Rear TypeI
Rear lift (at 24"/610mm)1,700 lbs [771 kg]

Electrical System of John Deere, 4210

Battery voltage, charging system and ground.

GroundNegative
Battery CCA500
55 OptOptional
Charging systemAlternator
Battery volts12
Charging amps40

Frequently asked questions

How much horsepower does the John Deere 4210 have?

The John Deere 4210 delivers 27 HP.

What years was the John Deere 4210 produced?

The John Deere 4210 was produced in 2002-2004.

What engine does the John Deere 4210 have?

The John Deere 4210 is powered by a Diesel, 3-cylinder engine.

What transmission does the John Deere 4210 use?

The John Deere 4210 uses a SyncShift transmission.

Is the John Deere 4210 4WD?

The John Deere 4210 is available in 2WD/4WD.

Compare the John Deere 4210 with another model